Mantis 5000 Especificaciones descargar pdf (Pagina 43)

4. Turn on the instrument on and allow it to warm up (approximately 2 hours).

5. Set the instrument to Zero order using the Align application. See Installation step 14

6. Once the instrument is warmed up, remove the reflectance standards from the ports (if

they are currently loaded). Load the reflectance lens into the small spot kit lens mount.

The reflectance lens is marked "R", the transmission lens is marked "T", and the centre-

mount lens is marked "C". The lens should be oriented so the arrow points toward the

integrating sphere. Gently rotate the lens until it clips into place. The grooves in the

outside of the lens sit on the clips on the mount.

7. Remove the transmission holder. (The transmission holder may clip the beam,

reducing the energy entering the sphere.)

7. Install the DRA into the instrument. Turn the instrument ON and allow it to initialize.

8. Install a beam blocker over the reference beam entrance port.

9. Find the sample beam at mirror M2 and centre if necessary.

10. Fully close the iris. Look at the top left hand corner of M3 and observe the beam on

the back of the iris. When the iris is closed to its smallest opening size, the beam should

be taller than the hole but centreed in the iris opening. To realign the iris assembly in the

beam path, first loosen the thumb screw that secures the two sections of the iris assembly

together. Move the top portion of the iris assembly, sliding it laterally, until the beam is

centreed on the iris opening. Retighten the thumb screw.

11. Fully open the iris. Dim the light in the room.

12. Adjust mirror M2 to centre the beam on the M3 SSK mirror. See Alignment

for

instruction on aligning the mirrors.

13. Hold the translucent paper just outside the open reflectance port. Adjust the M3 SSK

to centre the sample beam within the reflectance port opening. It may be necessary to

adjust the aperture size of the iris or relocate the lens mount along the dovetail rail to

achieve the desired spot size and make a note of the position of the iris.

1 2 ... 38 39 40 41 42 43 44 45 46 47 48 ... 87 88

Comentarios a estos manuales

Sin comentarios

Chief LT-P2045P Manuale (2 pagine)

Marchio: Chief | Categoria: Mounting kits | Dimensione: 0.05 MB |

Indice

FSB-4120

CAUTION!

Figure 3 Figure 4

Figure 5

Più prodotti e manuali per Kit di montaggio Chief

Modelli	Tipo di Documento
FSB4223B	Manuale Chief FSB4223B mounting kit, 3 pagine
FSB4200B	Manuale Chief FSB4200B mounting kit, 1 pagine
FSB4228B	Manuale Chief FSB4228B mounting kit, 2 pagine
FSB4239B	Manuale delle Istruzioni Chief FSB4239B mounting kit, 2 pagine
FCA820	Manuale di Installazione Chief FCA820 mounting kit, 12 pagine
FSB4236S	Manuale Chief FSB4236B mounting kit, 2 pagine
FSB4203B	Manuale Chief FSB4203B mounting kit, 1 pagine
FSB4204S	Manuale Chief FSB4204B mounting kit, 1 pagine
CMSUNVU	Manuale Chief CMSUNVU mounting kit, 4 pagine
FCA810	Manuale Chief FCA810 mounting kit, 16 pagine
FCA841	Manuale Chief FCA841 mounting kit, 12 pagine
SLB308	Manuale di Installazione Chief SLB308 mounting kit, 1 pagine
FSB4229B	Manuale Chief FSB4229B mounting kit, 1 pagine
FCA106	Manuale Chief FCA106 mounting kit, 4 pagine
FSB4394B	Manuale Chief FSB4394 mounting kit, 2 pagine
FSB4207S	Manuale Chief FSB4207S mounting kit, 1 pagine
KRA220B	Manuale di Installazione Chief KRA220B mounting kit, 8 pagine
FSB4202B	Manuale Chief FSB4202B mounting kit [no] , 1 pagine
CMA473	Specifiche Chief CMA473 mounting kit, 8 pagine
CMS1RU	Manuale di Installazione Chief CMS1RU mounting kit, 4 pagine

Mantis 5000 Especificaciones Pagina 43

Comentarios a estos manuales

Chief LT-P2045P manuali

Chief LT-P2045P Manuale (2 pagine)

Indice

Più prodotti e manuali per Kit di montaggio Chief

Mantis 5000 Especificaciones Pagina 43

Comentarios a estos manuales

Relacionado con productos y manuales para Cortadoras De Troncos Mantis 5000

Chief LT-P2045P manuali

Chief LT-P2045P Manuale (2 pagine)

Indice

Più prodotti e manuali per Kit di montaggio Chief